Why your cartons collapse in monsoon season (and how to fix it)

By Adithya G Udupa, 21 October 2026

Every year, Indian manufacturers face the same problem: boxes that passed a dry lab test in February are collapsing on pallets by July. Products arrive damaged. Customers complain. The packaging team gets blamed. And the root cause is almost always the same — nobody designed for the monsoon.

What humidity does to corrugated board

Corrugated board is made from cellulose fibres. Cellulose is hygroscopic, which means it absorbs moisture from the surrounding air. When the relative humidity in a warehouse climbs above 70% — which is routine in Mumbai, Chennai, Kochi and most of coastal India from June to September — the fibres in your board soften and lose their ability to resist compression.

The numbers are stark. A box tested at 50% relative humidity might show a Box Compression Test (BCT) result of 400 kg. The same box, conditioned at 85% relative humidity for 24 hours, might test at 160–200 kg. That is a 50–60% reduction in strength. If your pallet stack requires 300 kg of compression resistance from the bottom box, you have a problem.

The McKee formula and why the safety factor matters

The McKee formula is the standard way to estimate BCT from board properties:

BCT = 5.87 × ECT × √(board thickness × box perimeter)

The formula gives you a dry-condition estimate. To account for real-world conditions, you apply a safety factor — a multiplier that tells you how much stronger your box needs to be than the bare stack load.

For dry storage under two weeks, a factor of 3 is reasonable. For normal warehouse conditions up to two months, use 4. For humid or monsoon conditions, or storage beyond two months, use 5.

This means a box storing 10 kg of product in a stack of 5 (load = 40 kg) needs a BCT of at least 120 kg in dry conditions — but 200 kg in a monsoon warehouse. If your current board grade only delivers 180 kg BCT, you will see failures in the wet months even though it passed in February.

Use our free box strength calculator to check your current board grade →

The most common mistakes

Designing for the lab, not the warehouse. Most packaging engineers test at standard conditions (23°C, 50% RH). That is fine for a baseline, but it does not represent a Chennai warehouse in August. Always ask: where will this box actually sit, and for how long?

Using E-flute or B-flute for long-duration storage. Thinner boards lose strength faster in humidity because the fluting has less material to resist compression. If your product sits in a warehouse for more than a month during monsoon season, start with at least C-flute 44 ECT or BC double wall.

Ignoring print coverage. Heavy print coverage — especially full-bleed dark colours — stiffens the outer liner and can reduce BCT by 10–15%. This is rarely accounted for in standard calculations.

Stacking misalignment. Even a 10 mm offset between boxes in a stack can reduce effective BCT by 30%. If your warehouse stacks by hand, build in extra margin.

Practical fixes

  1. Run the calculation with the monsoon storage factor. Use a factor of 5 for any product stored in a non-climate-controlled warehouse during June–September. If your current board grade fails, move up one grade.
  2. Specify board by ECT, not just flute type. “C-flute” is not a strength specification. “C-flute 44 ECT” is. Make sure your supplier understands the difference and tests to it.
  3. Consider moisture-resistant coatings for high-value products. A wax or clay coating on the outer liner can slow moisture absorption significantly. It adds cost, but it is cheaper than product damage claims.
  4. Test at realistic conditions. If you have access to a conditioning room, test your boxes at 85% RH for 24 hours before the compression test. If you do not, ask your board supplier for humidity-conditioned BCT data.
  5. Review your warehouse layout. Boxes stored near loading dock doors or under leaking roofs are exposed to much higher humidity than boxes in the centre of the warehouse. If you cannot control the environment, at least control where the most vulnerable products sit.

When to call an engineer

If you are seeing consistent damage during monsoon season and the fixes above have not solved it, the problem may be structural rather than just a board grade issue. Box geometry, flap overlap, joint quality and pallet pattern all affect how a box performs under load. A packaging engineer can review your current design and identify the specific failure mode.

Send us your box dimensions and we will check the numbers →

Try the Box Strength Calculator

Want an engineer to check your pack?

Book a free 30-min call and we'll look at it together.

Book a free call